1.0

Touchpad scroll speed

Adjusts the scroll delta generated by touchpad finger scrolling. Values lower than 1.0 make scrolling slower, values higher than 1.0 make scrolling faster. false

Whether edge scrolling is enabled

When enabled, touchpads that support edge scrolling will have that feature enabled. true

Whether two-finger scrolling is enabled

When enabled, touchpads that support two-finger scrolling will have that feature enabled. true

Whether to disable the touchpad while typing

When enabled, touchpads will be disabled while typing on the keyboard. 500

Timeout in milliseconds until the touchpad is enabled after typing

Touchpads will be disabled for this many milliseconds after typing on the keyboard. true

Enable mouse clicks with touchpad

Set this to TRUE to be able to send mouse clicks by tapping on the touchpad. 'default'

Tap Button Map

Defines the mapping between the number of fingers and touchpad buttons. The default is to have a 1, 2 and 3 finger tap to map to the left, right and middle button ("lrm"), respectively. true

Enable tap-and-drag with touchpad

Set this to TRUE to be able to start a drag by tapping and immediately moving the finger that’s now pressed on the touchpad. false

Enable tap-and-drag-lock with touchpad

Set this to TRUE to lock the dragging process within a short timeout when the finger is lifted on the touchpad and the tap-and-drag setting is enabled. 'enabled'

Touchpad enabled

Defines the situations in which the touchpad is enabled. 'mouse'

Touchpad button orientation

Swap left and right mouse buttons for left-handed mice with “left”, “right” for right-handed, “mouse” to follow the mouse setting. 'default'

Pointer acceleration profile

Acceleration profile used for the connected devices of this type's pointers. The pointer acceleration profile can be set to either: - default (“default”) which uses the default acceleration profile for each device. - flat (“flat”), which accelerates by a device specific constant factor derived from the configured pointer speed. - adaptive (“adaptive”) which adapts the acceleration depending on the mouse movement. - custom ("custom") which accelerates by a provided acceleration curve defined with `pointer-step` and `pointer-speeds` in `custom-accel-config`. If a device doesn’t support the configured profile, “default” will be used. { "pointer-step": <@d 1.0>, "pointer-speeds": <@ad [0.0, 1.0]> }

Custom acceleration configuration

A dictionary storing custom device acceleration settings. Currently, valid entries are as follows: - `pointer-step` (d): The increment of an "x axis" of the pointer acceleration curve, the "input" pointer speed, in device units per millisecond. - `pointer-speeds` (ad): Every increment (N) of `pointer-step`, the Nth value is selected from this array as that point on the "y axis" of the pointer acceleration curve, the "output" pointer speed in device units per ms. Where input pointer speed doesn't lie on any single point in `pointer-step` and `pointer-speeds`, a linear interpolation of the two closest points will be calculated. Additional details can be found in libinput documentation ("The custom acceleration profile"). More entries may be added later. 0

Pointer speed

Pointer speed for the touchpad. Accepted values are in the [-1..1] range (from “unaccelerated” to “fast”). A value of 0 is the system default. true

Natural scrolling

Set this to TRUE to enable natural (reverse) scrolling for touchpads. 'fingers'

Click method

How to generate software-emulated buttons, either disabled (“none”), through specific areas (“areas”), number of fingers (“fingers”) or left as hardware default (“default”). false

Emulate middle click

Set this to TRUE to enable middle click during simultaneous left and right click. true

Keyboard repeat

Set this to TRUE to enable keyboard repeat. 30

Key Repeat Interval

Delay between repeats in milliseconds. 500

Initial Key Repeat Delay

Initial key repeat delay in milliseconds. true

Remember NumLock state

When set to true, GNOME will remember the state of the NumLock LED between sessions. false

NumLock state

The remembered state of the NumLock LED. false

Mouse button orientation

Swap left and right mouse buttons for left-handed mice. 0

Pointer speed

Pointer speed for mice. Accepted values are in the [-1..1] range (from “unaccelerated” to “fast”). A value of 0 is the system default. false

Natural scrolling

Set this to TRUE to enable natural (reverse) scrolling for mice. 'default'

Pointer acceleration profile

Custom acceleration configuration

Emulate middle click

Set this to TRUE to enable middle click during simultaneous left and right click. 400

Double click time

Length of a double click in milliseconds. 8

Drag threshold

Distance before a drag is started. 0

Mouse wheel emulation button. 0 to disable the feature.

false

Mouse wheel emulation button lock

Set this to TRUE to enable button locking for the wheel emulation button. If enabled, the first click of the button enables scrolling, the second click disables scrolling again. ["", "", ""]

Drawing tablet mapping

EDID information of the output the tablet is mapped to. Must be in the format [vendor, product, serial]. ["","",""] relies on automatic mapping. 'absolute'

Tablet mapping

How input affects the pointer on the screen [0, 0, 0, 0]

Tablet area

Dead area padding around the active area, in percentages. Respectively applied to left,right,top and bottom sides. false

Tablet aspect ratio

Enable this to restrict the tablet area to match the aspect ratio of the output. false

Tablet left-handed mode

Enable this to allow physically rotating the tablet for left-handed setups [0, 0, 100, 100]

Stylus pressure curve

Set this to x1, y1 and x2, y2 of the pressure curve applied to the stylus. [0, 100]

Stylus pressure range

Set this to the percentage of the physical pressure range that should map to the logical range. [0, 0, 100, 100]

Eraser pressure curve

Set this to x1, y1 and x2, y2 of the pressure curve applied to the eraser. [0, 100]

Eraser pressure range

Set this to the percentage of the physical pressure range that should map to the logical range. 'default'

Eraser button mode

Set this to change the behavior of the eraser button. 'default'

Eraser button action

Set this to the button action triggered if the eraser button is in 'button' mode. ''

Key combination for the eraser button if in 'button' mode

The keyboard shortcut generated when the button is pressed for custom actions. 'right'

Button action

Stylus button action, this button is located along the pen handle. 'middle'

Secondary button action

Secondary stylus button action, this button is located along the pen handle on some styli like the Grip Pen. Other styli like the Airbrush Pen or the Inking Pen only have one button, this setting is ineffective on those. 'default'

Tertiary button action

Tertiary stylus button action, this button is located along the pen handle on some styli like the 3D Pen. Other styli like the Grip Pen only have two buttons, this setting is ineffective on those. ''

Key combination for the primary button

The keyboard shortcut generated when the button is pressed for custom actions. ''

Key combination for the secondary button

The keyboard shortcut generated when the button is pressed for custom actions. ''

Key combination for the tertiary button

The keyboard shortcut generated when the button is pressed for custom actions. 'none'

Pad button action type

The type of action triggered by the button being pressed. ''

Key combination for the custom action

The keyboard shortcut generated when the button is pressed for custom actions. ["", "", ""]

Touchscreen output mapping

EDID information of the output the touchscreen is mapped to. Must be in the format [vendor, product, serial]. ["","",""] relies on automatic mapping. false

Whether the tablet’s orientation is locked, or rotated automatically.

Mouse wheel emulation button. 0 to disable the feature.

false

Mouse wheel emulation button lock

Set this to TRUE to enable button locking for the wheel emulation button. If enabled, the first click of the button enables scrolling, the second click disables scrolling again. 'default'

Pointer acceleration profile

Custom acceleration configuration

Emulate middle click

Set this to TRUE to enable middle click during simultaneous left and right click. 0

Pointer speed

Pointer speed for pointing sticks. Accepted values are in the [-1..1] range (from “unaccelerated” to “fast”). A value of 0 is the system default. 'default'

Pointer acceleration profile

Custom acceleration configuration

Scrolling method

Scrolling method used for pointing sticks. The scrolling method can be set to either default (“default”) which uses the default method, none (“none”), which disables scrolling, or middle-button (“on-button-down”) which enables scrolling whilst the middle button is held down.